Alvin WTB60 Manual de usuario

Busca en linea o descarga Manual de usuario para No Alvin WTB60. Alvin WTB60 User's Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 2
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Titan Drafting Tables
Tools required: Phillips screwdriver, awl, or drill with
1
16
" bit.
Assembly Instructions
Parts Included:
To Assemble Base Frame
Unpack and inspect contents to confirm
you have all the parts listed above. Use
care to differentiate rear crossbar (
B
)
(34½" long) from footrest crossbar (
C
)
(35½" long).
Attach both rear crossbars (
B
) and the
footrest and support crossbars (
C
) to
one side frame (
A
) using 2" Allen bolts
(
H
). Tighten securely. Note: Threaded
barrels preattached to leg frames must
be in rear and facing out.
Attach other side frame (
A
) to opposite
ends of crossbars in step two using 2"
Allen bolts (
H
). Tighten securely.
Place dust cover (
D
) over top of base
frame and attach using ¾" Phillips
screws (
I
). Note: Wooden strip on dust
cover should be in front of table and
facing up.
Attach hinge assemblies (
G
) to side
frames into pre-drilled holes using
¾" Phillips screws (
I
) as shown in
diagram. Pay close attention to correct
orientation of left and right hinges.
Tighten securely.
Insert tilt adjustment rods (
F
) into
threaded barrels on each side frame.
1
2
3
For WTB42, WTB48, WTB60,
WTB42-WA, and WTB48-WA
4
5
6
Screw adjustment knobs (
E
) into threaded barrels on each side frame. Set
adjustment rods so that connecting brackets are about 2" above side frames
for the time being with rods facing straight up and down and rear mounting
brackets facing out, as shown in diagram. Tighten knobs securely.
Base frame assembly is now complete. Set aside.
8
7
B 2pcs
Rear Crossbars
(34
7
8
" long)
B
C
B
C
A 2pcs
Side Frames,
Left & Right
B
C
D 1pc
B
C
Dust Cover w/ Drawer
Footrest & Support Crossbars
(35
7
8
" long)
B
C
B
C
C 2pcs
DRAFTING HEIGHT
W/ DRAWER
H 16pcs
2" Allen Bolts
B
C
I 20pcs
¾" Phillips Screws
B
C
G 2pcs
Hinge Assemblies,
Left & Right
B
C
J 1pc
Allen Wrench Key
B
C
E 2pcs
Adjustment Knobs
Tilt Adjustment Rods
B
C
F 2pcs
Vista de pagina 0
1 2

Indice de contenidos

Pagina 1 - Titan Drafting Tables

Titan Drafting Tables Tools required: Phillips screwdriver, awl, or drill with 1⁄16" bit.Assembly InstructionsParts Included:To Assemble Base Fra

Pagina 2 - Front Edge

©2008 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll

Comentarios a estos manuales

Sin comentarios